Crusader MP 5.0L Manual de servicio descargar pdf (Pagina 12)

Engine Mechanical Speciﬁcations (5.0 L) (cont’d)

Application

Speciﬁcation

Metric English

Crankshaft

Crankshaft Bearing Clearance – Journal #1 – Production 0.018–0.053 mm 0.0007–0.0021 in

Crankshaft Bearing Clearance – Journal #2, #3, and #4 – Production 0.030–0.068 mm 0.0012–0.0027 in

Crankshaft Bearing Clearance – Journal #5 – Production 0.020–0.060 mm 0.0008–0.0024 in

Crankshaft Bearing Clearance – Journal #1 – Service 0.025–0.051 mm 0.0010–0.0020 in

Crankshaft Bearing Clearance – Journal #2, #3, and #4 – Service 0.025–0.064 mm 0.0010–0.0025 in

Crankshaft Bearing Clearance – Journal #5 – Service 0.038–0.063 mm 0.0015–0.0025 in

Crankshaft End Play 0.05–0.20 mm 0.002–0.008 in

Crankshaft Journal Diameter – Journal #1 62.189–62.212 mm 2.4484–2.4493 in

Crankshaft Journal Diameter – Journal #2, #3, and #4 62.181–62.207 mm 2.4481–2.4491 in

Crankshaft Journal Diameter – Journal #5 62.185–62.207 mm 2.4482–2.4491 in

Crankshaft Journal Out-of-Round – Production 0.005 mm – Maximum 0.0002 in – Maximum

Crankshaft Journal Out-of-Round – Service 0.025 mm – Maximum 0.0010 in – Maximum

Crankshaft Journal Taper – Production 0.005 mm – Maximum 0.0002 in – Maximum

Crankshaft Journal Taper – Service 0.025 mm – Maximum 0.0010 in – Maximum

Crankshaft Runout at Rear Flange 0.038 mm 0.0015 in

Cylinder Bore

Diameter 94.894–94.947 mm 3.7360–3.7381 in

Out-of-Round – Production 0.025 mm 0.0010 in

Out-of-Round – Service 0.05 mm 0.002 in

Taper – Production – Relief Side 0.025 mm 0.0010 in

Taper – Production – Thrust Side 0.012 mm 0.0005 in

Taper – Service Limit 0.025 mm 0.0010 in

Cylinder Head

Surface Flatness – Engine Block Deck 0.10 mm 0.004 in

Surface Flatness – Exhaust Manifold Deck 0.05 mm 0.002 in

Surface Flatness – Intake Manifold Deck 0.10 mm 0.004 in

Exhaust Manifold

Surface Flatness – Flange to Flange 0.25 mm 0.010 in

Surface Flatness – Individual Flange 0.05 mm 0.002 in

Piston

Piston Bore Clearance – Production 0.018–0.061 mm 0.0007–0.0024 in

Piston Bore Clearance – Service 0.018–0.068 mm 0.0007–0.0026 in

Piston Pin

Clearance in Piston – Production 0.010–0.020 mm 0.0004–0.0008 in

Clearance in Piston – Service 0.013–0.025 mm 0.0005–0.0010 in

Diameter 23.545–23.548 mm 0.9270–0.9271 in

Interference Fit in Connecting Rod 0.012–0.050 mm 0.0004–0.0019 in

Piston Rings – End Gap Measured in Cylinder Bore

Piston Compression Ring Gap – Production – Top Groove 0.25–0.51 mm 0.010–0.020 in

Piston Compression Ring Gap – Production – 2nd Groove 0.46–0.66 mm 0.018–0.026 in

Piston Compression Ring Gap – Service – Top Groove 0.25–0.65 mm 0.010–0.025 in

Piston Compression Ring Gap – Service – 2nd Groove 0.46–0.90 mm 0.018–0.035 in

Piston Compression Ring Groove Clearance – Production – Top

Groove

0.030–0.070 mm 0.0012–0.0027 in

Piston Compression Ring Groove Clearance – Production –

2nd Groove

0.030–0.074 mm 0.0012–0.003 in

6-4 Engine Mechanical - 5.0L and 5.7L Engine

2002 - Unit Repair (May 25, 2001)

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 159 160

Comentarios a estos manuales

Sin comentarios

Crusader MP 5.0L Manual de servicio Pagina 12

Comentarios a estos manuales